Mini Minds Hub · Free printable
Build a Robot Bee: Free Printable Worksheet for Year 9
- ForYear 9
- StageKey Stage 3
- CostFree
- FormatPrintable PDF
Build a Robot Bee is a design and technology worksheet for Year 9 (ages 13 to 14). Pupils choose sensors for a robot bee, link inputs to outputs and test their design in three tricky situations. It takes about 20 minutes and needs only a pencil. Page 2 gives the grown-up notes, help ideas, a stretch task and the answers.
Before pupils start, model one chain on the board in the order input, process, output. Use an example that is not on the sheet, such as an automatic shop door. The usual slip is writing what the sensor notices instead of what the bee does. For every answer, ask "What does the motor, buzzer or LED do?"
What is on the sheet
Pupils design a robot bee by choosing from a list of sensors, including colour, light, distance and rain sensors and a microphone. They tick off a checklist and write what the bee does for different sensor readings. They name an input that could trigger a buzzer and complete an IF and THEN rule. Finally they test the bee in three tricky situations, such as a gust of wind or rain starting. There are numbered questions and lines for writing.
- Colour sensor to spot flower heads
- Light sensor to find daylight
- Distance sensor to avoid obstacles
- Rain sensor to spot wet weather
- Microphone to record songs
- Input: the colour sensor reads yellow. Write the output.
- Input: the distance sensor reads 5 cm from a wall. Write the output.
- Output: a buzzer sounds. Name an input that could trigger it.
- Process: IF light is low THEN do something. Write a sensible output.
- A gust of wind pushes the bee towards a wall.
- Rain starts while the bee is on a flower.
Worked example: a greenhouse vent
A greenhouse has a temperature sensor and a motor that opens a vent. The rule is: IF the temperature is above 30 degrees THEN open the vent. The sensor reads 35 degrees. What happens?
This example uses a greenhouse and different numbers, so it is a separate problem from the sheet. It shows two ways to trace a control system.
Method 1: input, process, output- Input: the temperature sensor reads 35 degrees.
- Process: the controller checks the rule. Is 35 above 30? Yes.
- Output: because the condition is true, the motor opens the vent.
- Draw three boxes in a row: sensor, controller, motor.
- Write the reading, 35 degrees, above the first arrow.
- Write the decision above the second arrow: above 30, so open.
- Write the action under the last box: vent opens.
How to design a control system
Start with the job
Write one sentence about what the bee must do. A clear job tells you which sensors you need and which ones are not needed.
Match each sensor to a need
Ask what the bee must know about the world. Then pick the sensor that measures exactly that. A sensor that measures something else will not help.
Write the rule
Use IF and THEN. Name the condition first, then the output. Keep each rule to one job so it is easy to check.
Test the awkward cases
Imagine something going wrong or two things happening at once. Trace each case from input to process to output and see whether the rule still works.
Why a robot bee?
Real bees move pollen from flower to flower, which helps many plants make seeds and fruit. Engineers sometimes look at animals for design ideas, so a bee is a good starting point for thinking about a small machine that must sense its surroundings and act on what it finds. It makes a clear, memorable design brief for Year 9.
Most electronic products follow a simple pattern. Inputs, such as sensors, send information to a controller. The controller follows rules, which is the process. Outputs, such as motors, buzzers and LEDs, then do something. Learning to trace that pattern helps pupils understand everything from a doorbell to a car. A bee that must cope with the weather and obstacles shows why good rules matter.
Bee facts
- Bees feed on nectar and pollen from flowers.
- When a bee visits flowers, it carries pollen from one flower to another.
- Bees have two pairs of wings.
- A bee has five eyes: two large ones and three small ones.
- Honey bees live together in groups called colonies.
Skills and curriculum link
- Choosing sensors
- Linking inputs to outputs
- Tracing a control system
- Writing IF and THEN rules
- Testing a design
- Explaining decisions
Ideas for helping
- InputAn input is information going into a system. A sensor collects it and sends it to the controller.
- ProcessThe process is the decision. The controller checks the input against a rule and chooses what happens next.
- OutputAn output is what the system does, such as moving, lighting up or making a sound. Ask which component does it.
- Choosing a sensorAsk what the bee needs to know, then ask which sensor can measure that. The match should be clear and direct.
Key words
- SensorA part that detects something in the world, such as light or distance, and sends a signal.
- ControllerThe part that reads the inputs and decides what the outputs should do.
- InputInformation that goes into a system.
- OutputWhat a system does as a result, such as a sound, a light or a movement.
- ProcessThe step in the middle where the controller follows its rules.
- IF and THENA rule that says: if this condition is true, then do this action.
How to use it
- Print both pages. Page 1 is for the pupil. Keep page 2 for the grown-up.
- Read the list of sensors together. Ask what each one could tell the bee about the world.
- Work through Part B together the first time. Say input, process and output out loud for each answer.
- Let the pupil attempt the tricky situations alone. Allow about 20 minutes in total.
- Check against page 2. Ask the pupil to explain each choice, not only give the answer.
Help, stretch and game ideas
If it feels too hard
Give a word bank: sensor, controller, motor, buzzer, LED, IF, THEN. Complete Part B together first. For each answer, ask two questions: what does the bee sense, and what does it do next? Then let the pupil try the next part alone.
To stretch confident children
Ask pupils to write the Part C rules as IF and THEN lines, then decide which rule is checked first. Ask them to explain their choice in one sentence. What should happen if two rules want different things at the same time?
Make it a game
Work in pairs. Swap sheets and act as the bee controller. One partner reads out each situation as a sensor reading, and the other says the output. Swap roles, then compare your answers with page 2.
Mistakes to watch for
Watch forThe pupil writes what the sensor notices instead of what the bee does.
Try thisAsk which component moves, lights up or makes a sound. The answer should name an action, not a reading.
Watch forThe pupil picks a sensor that cannot measure the thing the bee needs to know.
Try thisAsk what the sensor actually measures. Then check that it matches the need before moving on.
Watch forThe rule is vague, such as "the bee reacts".
Try thisAsk for a clear condition after IF and a clear action after THEN. Someone else should be able to build it from the words.
Talk about it
- Which sensor would you keep if the bee could only have one? Why?
- What is the difference between an input and an output?
- Where do you see IF and THEN rules in everyday life?
- What could go wrong if a robot had no distance sensor?
- What would you add to the bee to make it safer or more useful?
- Which situation was hardest to plan for, and why?
Take it off the page
Human controller
One person acts as the sensor, calling out readings. Another is the controller and follows IF and THEN rules. A third acts out the output.
Everyday flowcharts
Draw an input, process, output chain for a product at home, such as an automatic light or a door alarm. Label each part.
Design a helper robot
Sketch a small robot for a job at school or home. List its sensors and outputs, then write three IF and THEN rules.
Who it is for
Parents
Sit with your pupil for the first section, then let them lead. You do not need electronics knowledge. Ask "What does it sense, and what does it do?" and check with page 2. About 20 minutes is enough.
Teachers
Use it as a starter or homework before a systems and control project. It also works as a plenary or cover task. Page 2 has support and stretch ideas, so it suits mixed ability groups without extra preparation.
Home educators
Print it as part of a wider design and technology plan. It pairs well with building a simple circuit, a flowchart task or a nature walk to look at how bees behave. Reuse it later for revision.
Where this skill fits
Before this sheet, pupils usually meet simple circuits, switches and the idea that components have jobs. They may have drawn basic systems as boxes and arrows. This sheet builds on that by asking them to choose components for a purpose and to explain how a decision is made.
After it, pupils can move on to writing flowcharts and programming a microcontroller to follow rules. In Key Stage 3 design and technology, electronic systems and control sit alongside designing and making. This sheet is a short step towards a full systems and control project.
Questions parents and teachers ask
- What age is Build a Robot Bee for?
It is written for Year 9 (ages 13 to 14), in Key Stage 3. It suits pupils who are ready to give reasons for design choices, and it can also help older Year 8 pupils who enjoy electronics.
- What will pupils practise?
Pupils practise choosing sensors, linking inputs to outputs and tracing a control system. They also write an IF and THEN rule and test a design against tricky situations, which builds the habit of checking a design.
- How long does it take?
It takes about 20 minutes. Some pupils may finish sooner, and others may want longer to think about the tricky situations. Page 2 has a stretch idea for those who finish early.
- What if it feels too hard?
Give a word bank and work through Part B together first. The words are sensor, controller, motor, buzzer, LED, IF and THEN. Then ask what the bee senses and what it does next, and let the pupil try the next part alone.
- Do pupils need any electronics equipment?
No. The sheet needs only a pencil and paper. Pupils work out how a control system behaves by thinking and writing, so there is nothing to build or plug in.
- Is it suitable for use in class?
Yes. Teachers can use it as a starter, plenary, early finisher task, homework or table activity. It needs no preparation beyond printing, and page 2 includes help and stretch ideas for different needs.
- Do I need to print in colour?
No. It prints well in black and white on plain A4 paper. Print both pages, give page 1 to the pupil and keep page 2 with the answers for the grown-up.
Preview the full PDF
Made by Jaques of London, making games for families since 1795. A printable supports classroom learning and does not replace a teacher.